Any help with K04 data for group range 90-98

Wanting to explore comparing your K04 data to mine and how the data may tell the condition of the cam chain and/or tensioner. I was watching data in 091, I believe it was, and the duty going into the 60% range while raising rpm's in park. This gave me the idea that with help from others data and knowing the condition of your tensioner, hopefully near new, that I could compare the cam adjustment value to my own and perhaps figure what the data should be and where mine is at currently.

Any help is helpful...even if you are still running the original chain and tensioner as I am @ 144k miles. I'd say tuned K04 data is best just because I believe K03 data, tuned or not, could look different. So yeah, this is for tuned K04 BPY or like engine data.

I was able to find some time and check how mine is and I've done a short log for you.

Group 91 - Field 0 Group 91 - Field 1 Group 91 - Field 2 Group 91 - Field 3 Group 94 - Field 1
Engine Speed - (G28) Cam. Adjustment - Intake Bank 1 Cam. Adjustment - Intake B1 (spec.) Cam. Adjustment - Intake B1 (act.) Cam. Adjustment - Intake B1 (act.)
/min % °KW °KW °KW
720 5.9 28 26 27.5
720 5.9 28 24.5 25.5
720 5.9 28 26 28
720 5.9 28 27.5 24
720 5.9 28 25.5 25.5
760 5.9 28 27.5 24
720 5.9 28 26 25.5
760 5.9 28 24 24
720 5.9 28 25.5 26
760 5.9 28 24 25
720 5.9 28 26 28
760 5.9 28 23.5 25
760 5.9 28 26 27.5
1000 5.9 28 24.5 24
1280 5.9 28 23.5 23
1480 5.9 28 24 23.5
1800 5.9 28 24 23.5
2240 5.9 28 24 23.5
2880 5.9 28 25.5 24
3280 5.9 28 24.5 24.5
3480 5.9 28 25 25
3720 5.9 28 25.5 25.5
3840 5.9 28 25 25
4000 5.9 28 25 25
4080 5.9 28 24.5 26
4160 5.9 28 25 26
4200 5.9 28 26 26
4280 5.9 28 25.5 24.5
4160 5.9 28 26 26
3920 5.9 28 25 24.5
3520 5.9 28 25 26
3280 5.9 28 26 24.5
2720 5.9 28 25 24
2120 5.9 28 24.5 23.5
1520 5.9 28 24 23.5
1240 5.9 28 23 24
960 5.9 28 24.5 23.5
800 5.9 28 24.5 24.5
800 5.9 28 23.5 23.5
760 5.9 28 28 27.5
760 5.9 28 25 24.5
760 5.9 28 27.5 24
760 5.9 28 25.5 26.5
760 5.9 28 27.5 24

Engine was at operating temp, done in neutral while parked. Cam chain and tensioner were replaced at 120000km. Car has 240000km now.
Hope this helps.

Great, thank you...I will do mine again. Will take it to operating temp and log 091 again and rev it to 4k rpm. I believe mine may look worse. Cannot remember what I revved it to before when it reached 60%...but I can measure to what yours did. I know it must be close to needing replacing of the cam chain and tensioner. Nearing 150k miles now. Want to replace those and the camshaft position sensor as well. My N205 was already replaced not long ago. I have a small leak at the oil cooler now and will replace the two seals for the oil filter and cooler and the two knock sensors when I do that job.

I will post my log data when I get it...hopefully the data posted here will help someone know when their adjuster is nearing the end. I imagine if not reaching 100% adjustment...it should be OK yet. Thank you again.