GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Mk6 GTI Steering Wheel to Mk5 GTI

jakethemoss

Ready to race!
Location
Denmark
Car(s)
Mercedes Sprinter

vagike

Newbie
Location
Edmonton
actually you can reuse the airbag itself, but you need a revision C slipring, steering coloumn controller needs to bee a CH revision, and if you have cruise control, the stalk has to be replaced with the 1K0 953 513 G stalk from the Mk 6.
i have function in 10 of the 12 buttons on the sw. you should be able to gain function of all 12 buttons, but i believe it requires the latest revision canbus gateway. :thumbsup:
The revised canbus; do i have to get that done by a dealership?
 

vagike

Newbie
Location
Edmonton
i fitted the wheel today along with mk6 ch module new slip ring and mk6 stalk. wheel works horn and buttons ok but I have yellow steering light on that i cant get off. I have tried the full left full right drive forward adaptation thingy about 20 times to no avail.
the fault codes I have are
Thursday,23,December,2010,12:10:13:46862
VCDS Version: Release 10.6.0
Data version: 20100630



--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Chassis Type: 1K0
Scan: 01 03 09 15 16 17 19 25 37 42 44 46 52 56

VIN: WV1ZZZ2KZ5X091434 Mileage: 126730km/78746miles

00-Steering Angle Sensor -- Status: OK 0000
01-Engine -- Status: Malfunction 0010
03-ABS Brakes -- Status: OK 0000
09-Cent. Elect. -- Status: Malfunction 0010
15-Airbags -- Status: OK 0000
16-Steering wheel -- Status: Malfunction 0010
17-Instruments -- Status: Malfunction 0010
19-CAN Gateway -- Status: OK 0000
25-Immobilizer -- Status: OK 0000
37-Navigation -- Status: OK 0000
42-Door Elect, Driver -- Status: OK 0000
44-Steering Assist -- Status: Malfunction 0010
46-Central Conv. -- Status: OK 0000
52-Door Elect, Pass. -- Status: OK 0000
56-Radio -- Status: Malfunction 0010

-------------------------------------------------------------------------------


-------------------------------------------------------------------------------
Address 09: Cent. Elect. Labels: 3C0-937-049-23-M.lbl
Part No SW: 1K0 937 049 M HW: 1K0 937 049 M*
Component: Bordnetz-SG H37 0803
Revision: 00H37000 Serial number: 00000001623597
Coding: 00884F020004100000000000000000000008FB075C
Shop #: WSC 35110 377 08192
VCID: 39722FBA4F0384D4

Part No: 2K2 955 119 B
Component: Wischer VW357 012 0402
Coding: 00065493
Shop #: WSC 35110

1 Fault Found
01506 - Bulb for Rear Fog; Right (L47)
012 - Electrical Fault in Circuit

------------------------------------------------------------------------------

-------------------------------------------------------------------------------
Address 16: Steering wheel Labels: 1K0-953-549-MY9.lbl
Part No SW: 1K0 953 549 CH HW: 1K0 953 549 CH
Component: J0527 056 0111
Coding: 0000533
Shop #: WSC 12345 123 12345
VCID: 7AF0F0B60A854FCC

Part No: 5K0 959 542 A
Component: E221__MFL-TAS H07 0013
Coding: 00000130
Shop #: WSC 00000

1 Fault Found
00002 - Transmission Control Unit
004 - No Signal/Communication - Intermittent

-------------------------------------------------------------------------------
Address 17: Instruments Labels: 1K0-920-xxx-17.lbl
Part No: 2K0 920 941 C
Component: KOMBIINSTRUMENT VDD 0716
Coding: 0000403
Shop #: WSC 00874 210 55459
VCID: 2952FFFABFA33454

1 Fault Found
00003 - Control Module
014 - Defective

-------------------------------------------------------------------------------


-------------------------------------------------------------------------------
Address 44: Steering Assist Labels: 1Kx-909-14x.lbl
Part No: 1K2 909 144 H
Component: EPS_ZFLS Kl.12 1502
Shop #: WSC 00000 000 00000
VCID: 3162179A97734C94

2 Faults Found
00778 - Steering Angle Sensor (G85)
014 - Defective
Freeze Frame:

02546 - Steering Limit Stop
005 - No or Incorrect Basic Setting / Adaptation
Freeze Frame:
Mileage: 6720 km
Temperature: 9.0°C
Voltage: 14.50 V
Voltage: 14.30 V

Any help would be very greatfully received
email Ross-Tech I believe they have a procedure.
 

jakethemoss

Ready to race!
Location
Denmark
Car(s)
Mercedes Sprinter
The revised canbus; do i have to get that done by a dealership?
nope, VCDS and remember to copy/write which boxes is ticked in the old before you remove it :thumbsup:
 

problemchild75

New member
Location
manchester
:mad: just been out to try the links above again to no avail. im really at a loss any ideas. with the g85 fault saying defective im thinking it may be more of a prob . has any one else had the defective message
cheers
 

problemchild75

New member
Location
manchester
:D YIPEEEEE all sorted now. when i put new steering module on the pin connecters were slightly different and when i connected it to the G85 one of the pins had bent and not connected properley. re fitted it after straightening the pins (carefully) and re did the adaptions (took two mins) and we are all good all working properley and no fault codes. :D :D :D :D its much easier stripping and fitting the modules and wheel second time round, the whole lot took me 40mins
thanks for all your help im off to pub now for a christmas drink much happier than I would of been.
next stop highline clocks :D
forgot to say its not for my golf but my caddy van lol
 

SuperDave

New member
Location
The Netherlands
Hi guys, I bought already a new steering wheel.

But I need to buy the electronic Steer module, is it 1K0 953 549 CH and higer?
Because I can buy 1K0 953 549 CQ.

Thanks
 

jakethemoss

Ready to race!
Location
Denmark
Car(s)
Mercedes Sprinter
CQ should be fine
 

golf for life

Ready to race!
Location
Israel
Hi guys, I bought already a new steering wheel.

But I need to buy the electronic Steer module, is it 1K0 953 549 CH and higer?
Because I can buy 1K0 953 549 CQ.

Thanks
CQ is NOT!!!! fine
what kind of steering wheel do you have? with multifunction buttons or without?
what car do you have? from what I see it is a mk4 TDI, if it really is a mk4 than you don't need to buy anything just need to a retrofit to the airbag wiring(also you should know that the airbag will probably not work because of the car incompatability)
http://uk-mkivs.net/forums/t/307600.aspx

you should also read this
http://uk-mkivs.net/forums/t/331134.aspx
 

jakethemoss

Ready to race!
Location
Denmark
Car(s)
Mercedes Sprinter
Hmm, the tread is called mk 6 sw to mk 5, so i asume he has a mk 5.
Why do you find CQ to not be fine??
 

golf for life

Ready to race!
Location
Israel
Hmm, the tread is called mk 6 sw to mk 5, so i asume he has a mk 5.
Why do you find CQ to not be fine??
if you want to know what is compatible you can look at this page from ross tech wiki
http://wiki.ross-tech.com/wiki/index.php/Steering_Wheel_Control_Module_Versions

as you can see CQ is a midline module so it is only compatible with the non multifunction mk6 steering wheel
second it does not have the steering angle sensor, so it will cause many fault codes.
the moduls that are compatible to a mk5 to a mk6 multifinction steering wheel are the CH, CK(from the info on the page, I did not see anyone try to do it with this module) and the CJ(I believe it can also fit)
if you have a steering wheel without multifunction buttons(I have to mention that I see no point in doing this kind of retrofit, if someone already buys the steering module and a new steering wheel why not getting a multifunction ones for almost the same price)
I believe that CN and CM will be alright for this kind of retrofit
 

SuperDave

New member
Location
The Netherlands
Hi Guys,

I have bought a MK5, 9 months ago, I changed it in my profile.
But I saw already that CQ won't work.
Bought this,
MK6 steering wheel including MF (I don't have MF right now)
1K0953549CH (Steering module)
1K0953513G (CC MK6)
1K0953519H (Washer MK6)
1K0959653C
1K0907530AF (CAN Gateway)

I also bought 1K0953549BS (from Scirocco 3), only the LIN version(v1.3) and Software (SW 0101) version are different. Is the BS version also working?
 

jakethemoss

Ready to race!
Location
Denmark
Car(s)
Mercedes Sprinter
if you want to know what is compatible you can look at this page from ross tech wiki
http://wiki.ross-tech.com/wiki/index.php/Steering_Wheel_Control_Module_Versions

as you can see CQ is a midline module so it is only compatible with the non multifunction mk6 steering wheel
second it does not have the steering angle sensor, so it will cause many fault codes.
the moduls that are compatible to a mk5 to a mk6 multifinction steering wheel are the CH, CK(from the info on the page, I did not see anyone try to do it with this module) and the CJ(I believe it can also fit)
if you have a steering wheel without multifunction buttons(I have to mention that I see no point in doing this kind of retrofit, if someone already buys the steering module and a new steering wheel why not getting a multifunction ones for almost the same price)
I believe that CN and CM will be alright for this kind of retrofit
I stand corrected then, and thank you for your informative post :thumbsup:
 

golf for life

Ready to race!
Location
Israel
you are good to go, good luck:thumbsup:

about the BS module it will not work with the mk6 steering wheel. it will only work with the mk5 multifunction steering wheel.
use the CH module in your installation..


Hi Guys,

I have bought a MK5, 9 months ago, I changed it in my profile.
But I saw already that CQ won't work.
Bought this,
MK6 steering wheel including MF (I don't have MF right now)
1K0953549CH (Steering module)
1K0953513G (CC MK6)
1K0953519H (Washer MK6)
1K0959653C
1K0907530AF (CAN Gateway)

I also bought 1K0953549BS (from Scirocco 3), only the LIN version(v1.3) and Software (SW 0101) version are different. Is the BS version also working?
 

SI-R32

New member
Location
UK Medway Kent
cc stalk

Hi guys quick question about the cruise control stalk, the part number 1K0953513G which is from the mk6, has been used as far back as 2005 according to ETKA



or is it because its a new part that is fully backwards compatible with all golfs back to 2005, hope someone can answer as new steering wheel is on the way and i only had cruise retro fitted by vw 6 months ago and was hoping i didn't need a new stalk as well.

Also the CH control module is 150 quid from vw, 107 from eBay taiwan would you trust a purchase from there or just get it from VW.

Cheers guys

From a newbie
 
Top