GOLFMK8
GOLFMK7
GOLFMK6
GOLFMKV

Golf MK5 GTI DSG AWD Conversion

farisidrees

Passed Driver's Ed
Location
Lebanon
Car(s)
Golf 5 GTI
Phase 2:
Engine Bay Work


Today ABS module from AWD car will be installed.

AWD dsg transmission with T-case bolted to engine.

Installing Engine back.
 

Attachments

  • IMAG0070~01.jpg
    IMAG0070~01.jpg
    105.5 KB · Views: 3,969
  • IMAG0057~01.jpg
    IMAG0057~01.jpg
    226.6 KB · Views: 3,936
  • IMAG0060~01.jpg
    IMAG0060~01.jpg
    214.1 KB · Views: 3,931
  • IMAG0064~01.jpg
    IMAG0064~01.jpg
    229.3 KB · Views: 3,948

farisidrees

Passed Driver's Ed
Location
Lebanon
Car(s)
Golf 5 GTI
Interesting DSG cooler plate!
You're not worried that the oil will not warm up quick enough without the standard heat-exchanger?

I had monitored transmission fluid temp with this plate for several cases, cold start, idle, heavy and slow traffic, autoban cruise, and at all above cases it was warm enough. >78 degree
 

farisidrees

Passed Driver's Ed
Location
Lebanon
Car(s)
Golf 5 GTI
Finishing Engine bay work

Engine with new Gearbox are back into the car after ABS pump replacement
 

Attachments

  • IMAG0072.jpg
    IMAG0072.jpg
    234.5 KB · Views: 3,613
  • IMAG0074.jpg
    IMAG0074.jpg
    253 KB · Views: 3,595
  • IMAG0075.jpg
    IMAG0075.jpg
    284.8 KB · Views: 3,618
  • IMAG0076.jpg
    IMAG0076.jpg
    317.6 KB · Views: 3,616
  • IMAG0092.jpg
    IMAG0092.jpg
    376 KB · Views: 3,647

TypeR_126

Ready to race!
Location
Concord, CA
Car(s)
GTI
Out of curiosity, where are your catch can lines going to?

I could be mistaken, but it looks like they're just looping under the intake to the blue anodized can in front of the battery.
 

farisidrees

Passed Driver's Ed
Location
Lebanon
Car(s)
Golf 5 GTI
I could be mistaken, but it looks like they're just looping under the intake to the blue anodized can in front of the battery.

Yes you are mistaken, They are going to the silver plate (PCV plate) at the top of engine (just in front of the ignition coils).
 

Stranded in Daytona

Go Kart Champion
Location
Wilmington, NC
Car(s)
06 2 door TR GTI
Yes you are mistaken, They are going to the silver plate (PCV plate) at the top of engine (just in front of the ignition coils).

I was asking where those lines are going to from the PCV plate...

I think this guy:

I could be mistaken, but it looks like they're just looping under the intake to the blue anodized can in front of the battery.

Was right though. I didn't see the catch can on the other side of the intake.
 

DeWet

Ready to race!
Location
Australia
Drive shaft mounts removed from R32 welded and painted
Can you find these bits only from a wrecked R32? How did you measure exactly where they should be welded on?

Not too sure where I will be able to find these mounts as Im not close to a wrecker with European cars to go find these bits.

Can anyone maybe help me get these and post to Australia with paypal payment?



Sent from my SM-N920I using Tapatalk
 

DeWet

Ready to race!
Location
Australia
Can you find these bits only from a wrecked R32? How did you measure exactly where they should be welded on?

Not too sure where I will be able to find these mounts as Im not close to a wrecker with European cars to go find these bits.

Can anyone maybe help me get these and post to Australia with paypal payment?



Sent from my SM-N920I using Tapatalk
I manage to get the propshaft mounts and the heat shield from a wrecker in another state.

Last 2 things to sort is to swap out my mk70 abs for a mk60 that will work with the haldex 4 motion controller

Sent from my SM-N920I using Tapatalk
 
Top